The Dunu Alpha 3 is 32Ω at 105.0 dB (no reference unit printed); the Dunu Kima is 32Ω at 108.0 dB (no reference unit printed). This page covers what they ask of an amplifier, not how they sound.
The Alpha 3 needs 3.0 dB more than the Kima to reach the same loudness — 0.32 mW against 0.16 mW.
| Specification | Alpha 3 | Kima |
|---|---|---|
| Impedance | 32 Ω | 32 Ω |
| Sensitivity | 105.0 dB | 108.0 dB |
| Sensitivity (voltage) | 119.9 dB/V | 122.9 dB/V |
| Power for 100 dB | 0.32 mW | 0.16 mW |
| Voltage for 100 dB | 0.10 V | 71 mV |
| Current for 100 dB | 3.1 mA | 2.2 mA |
| Highest source impedance that leaves them alone (one-eighth rule) | 4.00 Ω | 4.00 Ω |
| Sources that reach 100 dB out of 280 | 280 | 280 |
One caution before reading the rows. Dunu Alpha 3 and Dunu Kima printed a decibel figure with no reference unit, so this page reads it as per milliwatt. If it is really per volt, each of them needs far more than the table says. Why the two readings differ by so much.
Every source in the database that drives one of them drives the other. On power, the choice between these two changes nothing about what amplifier you need.
3 sources stay below the audible-hiss threshold with the Alpha 3 but cross it with the Kima (FiiO BTR11, FiiO K11 R2R, Rupert Neve RNHP).
280 of the 280 sources here reach 100 dB on both.
The Alpha 3 is more demanding than 34% of the 567 non-electrostatic models in this database; the Kima than 23%.
| dB SPL | Alpha 3 power | Alpha 3 voltage | Kima power | Kima voltage |
|---|---|---|---|---|
| 80 | 3.2 µW | 10 mV | 1.6 µW | 7 mV |
| 85 | 0.01 mW | 18 mV | 5.0 µW | 13 mV |
| 90 | 0.03 mW | 32 mV | 0.02 mW | 23 mV |
| 95 | 0.10 mW | 57 mV | 0.05 mW | 40 mV |
| 100 | 0.32 mW | 0.10 V | 0.16 mW | 71 mV |
| 105 | 1.0 mW | 0.18 V | 0.50 mW | 0.13 V |
| Source | Price | Headroom, Alpha 3 | Headroom, Kima | Output impedance | Noise |
|---|---|---|---|---|---|
| JadeAudio JA11 | $20 | 19.8 dB | 22.8 dB | 0.5 Ω | 1.7 µV |
| FiiO KA11 | $29 | 28.0 dB | 31.0 dB | 0.7 Ω | 1.7 µV |
| FiiO BTR13 | $59 | 25.0 dB | 28.0 dB | 0.6 Ω | 1.0 µV |
Of the 280 sources here, 280 reach 100 dB on both. 66 of them also publish an output impedance low enough for both under the one-eighth rule and a noise figure that stays below the audible-hiss threshold with both.
The cheapest of the 66 is the JadeAudio JA11, at $20. It leaves 19.8 dB of headroom on the Alpha 3 and 22.8 dB on the Kima, its output impedance is 0.5 Ω against a one-eighth limit of 4.00 Ω for both, and its noise figure puts the hiss floor 15 dB and 12 dB below the 20 dB SPL this site treats as the point where a quiet room stops hiding it.
| Model | As printed | Tolerance | Standard |
|---|---|---|---|
| Alpha 3 | 5Hz-40kHz | not printed | not printed |
| Kima | 5Hz-40kHz | not printed | not printed |
Dunu prints the same thing for both the Alpha 3 and the Kima: 5Hz-40kHz.
Kima: Printed in the "Technical Info" block; DUNU gives the row no label of its own beyond that heading.
Neither range has a tolerance printed beside it, so the matching numbers say little.
Not a measurement; maker by maker.
Both have a page of their own. In full: Dunu Alpha 3 and Dunu Kima. Each figure on this page is labelled on those pages with where it came from, including the ones Dunu never published — what that maker publishes, counted.