The Dunu DN-142 is 37Ω at 107.0 dB/mW; the Dunu Titan S is 32Ω at 110.0 dB (no reference unit printed). This page covers what they ask of an amplifier, not how they sound.
The DN-142 needs 3.0 dB more than the Titan S to reach the same loudness — 0.20 mW against 0.10 mW.
| Specification | DN-142 | Titan S |
|---|---|---|
| Impedance | 37 Ω | 32 Ω |
| Sensitivity | 107.0 dB/mW | 110.0 dB |
| Sensitivity (voltage) | 121.3 dB/V | 124.9 dB/V |
| Power for 100 dB | 0.20 mW | 0.10 mW |
| Voltage for 100 dB | 86 mV | 57 mV |
| Current for 100 dB | 2.3 mA | 1.8 mA |
| Highest source impedance that leaves them alone (one-eighth rule) | 4.62 Ω | 4.00 Ω |
| Sources that reach 100 dB out of 280 | 280 | 280 |
One caution before reading the rows. Dunu Titan S printed a decibel figure with no reference unit, so this page reads it as per milliwatt. If it is really per volt, that model needs far more than the table says. Why the two readings differ by so much.
Every source in the database that drives one of them drives the other. On power, the choice between these two changes nothing about what amplifier you need.
9 sources stay below the audible-hiss threshold with the DN-142 but cross it with the Titan S (FiiO BTR11, FiiO K11 R2R, Lake People G103-S Mk II, 6 more).
280 of the 280 sources here reach 100 dB on both.
The DN-142 is more demanding than 26% of the 567 non-electrostatic models in this database; the Titan S than 15%.
| dB SPL | DN-142 power | DN-142 voltage | Titan S power | Titan S voltage |
|---|---|---|---|---|
| 80 | 2.0 µW | 9 mV | 1.0 µW | 6 mV |
| 85 | 6.3 µW | 15 mV | 3.2 µW | 10 mV |
| 90 | 0.02 mW | 27 mV | 0.01 mW | 18 mV |
| 95 | 0.06 mW | 48 mV | 0.03 mW | 32 mV |
| 100 | 0.20 mW | 86 mV | 0.10 mW | 57 mV |
| 105 | 0.63 mW | 0.15 V | 0.32 mW | 0.10 V |
| Source | Price | Headroom, DN-142 | Headroom, Titan S | Output impedance | Noise |
|---|---|---|---|---|---|
| JadeAudio JA11 | $20 | 21.1 dB | 24.8 dB | 0.5 Ω | 1.7 µV |
| FiiO KA11 | $29 | 29.4 dB | 33.0 dB | 0.7 Ω | 1.7 µV |
| FiiO BTR13 | $59 | 26.4 dB | 30.0 dB | 0.6 Ω | 1.0 µV |
Of the 280 sources here, 280 reach 100 dB on both. 62 of them also publish an output impedance low enough for both under the one-eighth rule and a noise figure that stays below the audible-hiss threshold with both.
The cheapest of the 62 is the JadeAudio JA11, at $20. It leaves 21.1 dB of headroom on the DN-142 and 24.8 dB on the Titan S, its output impedance is 0.5 Ω against a one-eighth limit of 4.62 Ω and 4.00 Ω, and its noise figure puts the hiss floor 14 dB and 10 dB below the 20 dB SPL this site treats as the point where a quiet room stops hiding it.
| Model | As printed | Tolerance | Standard |
|---|---|---|---|
| DN-142 | 5Hz – 40kHz | not printed | not printed |
| Titan S | 5 Hz – 40 kHz | not printed | not printed |
Dunu prints 5Hz – 40kHz for the DN-142 and 5 Hz – 40 kHz for the Titan S.
Neither range has a tolerance printed beside it, so a wider range on one sheet is not deeper bass or more treble.
Not a measurement; maker by maker.
Both have a page of their own. In full: Dunu DN-142 and Dunu Titan S. Each figure on this page is labelled on those pages with where it came from, including the ones Dunu never published — what that maker publishes, counted.