The Hidizs MP145 PRO is 30Ω at 104.0 dB (no reference unit printed); the Hidizs MY LIN is 17Ω at 111.0 dB (no reference unit printed). This page covers what they ask of an amplifier, not how they sound.
The MP145 PRO needs 7.0 dB more than the MY LIN to reach the same loudness — 0.40 mW against 0.08 mW.
| Specification | MP145 PRO | MY LIN |
|---|---|---|
| Impedance | 30 Ω | 17 Ω |
| Sensitivity | 104.0 dB | 111.0 dB |
| Sensitivity (voltage) | 119.2 dB/V | 128.7 dB/V |
| Power for 100 dB | 0.40 mW | 0.08 mW |
| Voltage for 100 dB | 0.11 V | 37 mV |
| Current for 100 dB | 3.6 mA | 2.2 mA |
| Highest source impedance that leaves them alone (one-eighth rule) | 3.75 Ω | 2.12 Ω |
| Sources that reach 100 dB out of 280 | 280 | 280 |
One caution before reading the rows. Hidizs MP145 PRO and Hidizs MY LIN printed a decibel figure with no reference unit, so this page reads it as per milliwatt. If it is really per volt, each of them needs far more than the table says. Why the two readings differ by so much.
Every source in the database that drives one of them drives the other. On power, the choice between these two changes nothing about what amplifier you need.
19 sources stay below the audible-hiss threshold with the MP145 PRO but cross it with the MY LIN (FiiO BTR11, Fosi Audio SK02, FiiO K11 R2R, 16 more).
280 of the 280 sources here reach 100 dB on both.
The MP145 PRO is more demanding than 35% of the 567 non-electrostatic models in this database; the MY LIN than 5%.
| dB SPL | MP145 PRO power | MP145 PRO voltage | MY LIN power | MY LIN voltage |
|---|---|---|---|---|
| 80 | 4.0 µW | 11 mV | 0.8 µW | 4 mV |
| 85 | 0.01 mW | 19 mV | 2.5 µW | 7 mV |
| 90 | 0.04 mW | 35 mV | 7.9 µW | 12 mV |
| 95 | 0.13 mW | 61 mV | 0.03 mW | 21 mV |
| 100 | 0.40 mW | 0.11 V | 0.08 mW | 37 mV |
| 105 | 1.3 mW | 0.19 V | 0.25 mW | 65 mV |
| Source | Price | Headroom, MP145 PRO | Headroom, MY LIN | Output impedance | Noise |
|---|---|---|---|---|---|
| JadeAudio JA11 | $20 | 18.5 dB | 23.0 dB | 0.5 Ω | 1.7 µV |
| FiiO KA11 | $29 | 27.1 dB | 34.8 dB | 0.7 Ω | 1.7 µV |
| FiiO BTR13 | $59 | 24.0 dB | 31.7 dB | 0.6 Ω | 1.0 µV |
Of the 280 sources here, 280 reach 100 dB on both. 53 of them also publish an output impedance low enough for both under the one-eighth rule and a noise figure that stays below the audible-hiss threshold with both.
The cheapest of the 53 is the JadeAudio JA11, at $20. It leaves 18.5 dB of headroom on the MP145 PRO and 23.0 dB on the MY LIN, its output impedance is 0.5 Ω against a one-eighth limit of 3.75 Ω and 2.12 Ω, and its noise figure puts the hiss floor 16 dB and 7 dB below the 20 dB SPL this site treats as the point where a quiet room stops hiding it.
| Model | As printed | Tolerance | Standard |
|---|---|---|---|
| MP145 PRO | 20Hz to 40kHz | not printed | not printed |
| MY LIN | 20Hz–40kHz | not printed | not printed |
Hidizs prints 20Hz to 40kHz for the MP145 PRO and 20Hz–40kHz for the MY LIN.
For both: Hidizs prints this figure in the body copy of the product page. The only specification table on that page belongs to a different product — one of the company’s DAC dongles — and there is no frequency row in a table for this model.
Neither range has a tolerance printed beside it, so a wider range on one sheet is not deeper bass or more treble.
Not a measurement; maker by maker.
Both have a page of their own. In full: Hidizs MP145 PRO and Hidizs MY LIN. Each figure on this page is labelled on those pages with where it came from, including the ones Hidizs never published — what that maker publishes, counted.