On power: 64 of the 65 audio interfaces here reach 100 dB SPL on the Dan Clark Audio Stealth. It needs 10 mW at its 23Ω, and 1 of them do not get there.
Power is one of three questions and the one that goes wrong least often. The other two — whether the source’s output impedance leaves the frequency response alone, and whether you will hear its noise floor — are answered further down, separately, because a source can pass one and fail another.
The 1 that fall short are Steinberg UR22C. The closest of them, the Steinberg UR22C, delivers 8.6 mW into 23Ω against the 10 mW needed — 0.6 dB short.
The cheapest one that does reach it is the Zoom AMS-22 at $100, which delivers 14 mW into 23Ω — 2 dB of headroom over the 10 mW this headphone needs for 100 dB SPL.
100 dB SPL is a peak level, not a listening level. If you listen at 85 dB the same headphone needs 0.32 mW, which is 15 dB less, and the answer above changes for most of the category. The model page has the full ladder.
Under the one-eighth rule the Dan Clark Audio Stealth wants a source below 2.88Ω. Of the 43 audio interfaces here that publish an output impedance, 15 are under it and 28 are not.
The furthest over is the Tascam US-2x2HR at 66Ω, which is 23× the ceiling. Above that threshold the source stops being a volume control and starts being part of the frequency response. The simulator shows what that looks like.
The other 22 publish nothing at all on this, so they are not on either side of that count. This site leaves them blank rather than assuming a figure.
Hiss depends on the source’s own noise floor and on how sensitive the headphone is. At 90.0 dB/mW and 23Ω, the Dan Clark Audio Stealth turns one microvolt of source noise into about -14 dB SPL — and the threshold where that stops being noticeable in a quiet room is around 20 dB SPL.
The one audio interface here that publishes a noise figure stays below that threshold with this headphone.
The remaining 64 publish no noise figure, so they cannot be placed on either side.
| Source | Price | Into 23Ω | Output impedance | Hiss in these | Power verdict |
|---|---|---|---|---|---|
| MOTU M2 | $219 | 240 mW | not published | not published | Comfortable |
| SSL 2 MkII | $229 | 269 mW | 1 Ω | not published | Comfortable |
| MOTU M4 | $279 | 240 mW | not published | not published | Comfortable |
| Apogee BOOM | $299 | 173 mW | 0.5 Ω | not published | Comfortable |
| SSL 2 Plus MkII | $299 | 269 mW | 1 Ω | not published | Comfortable |
| M-Audio AIR 192|14 | $329 | 115 mW | not published | not published | Comfortable |
| MOTU M6 | $499 | 240 mW | not published | not published | Comfortable |
| SSL 12 | $599 | 850 mW | 1 Ω | not published | Comfortable |
| Apogee Duet 3 | $649 | 850 mW | 0.5 Ω | not published | Comfortable |
| MOTU UltraLite-mk5 | $699 | 338 mW | 1 Ω | not published | Comfortable |
| Universal Audio Volt 876 | $999 | 162 mW | not published | not published | Comfortable |
| RME ADI-2 DAC FS | $1399 | 1.0 W | 0.1 Ω | not published | Comfortable |
Sorted by how many of the three questions the source answers well, then by price. A blank in a column is a blank in the manufacturer’s own documentation, not a zero.
The Dan Clark Audio Stealth on other categories: portable players · desktop amplifiers · desktop DAC/amps.
The Dan Clark Audio Stealth page has every source in the database against this headphone, and the matcher takes your own numbers.