The Beyerdynamic DT 240 Pro is 34Ω at 99.0 dB/mW; the Beyerdynamic DT 770 Pro (32Ω) is 32Ω at 96.0 dB (no reference unit printed). This page is only about what they ask of an amplifier — not how they sound, which no specification on either sheet can tell you.
The DT 770 Pro (32Ω) needs 3.0 dB more than the DT 240 Pro to reach the same loudness — 2.5 mW against 1.3 mW.
| Specification | DT 240 Pro | DT 770 Pro (32Ω) |
|---|---|---|
| Impedance | 34 Ω | 32 Ω |
| Sensitivity | 99.0 dB/mW | 96.0 dB |
| Sensitivity (voltage) | 113.7 dB/V | 110.9 dB/V |
| Power for 100 dB | 1.3 mW | 2.5 mW |
| Voltage for 100 dB | 0.21 V | 0.28 V |
| Current for 100 dB | 6.1 mA | 8.9 mA |
| Highest source impedance that leaves them alone (one-eighth rule) | 4.25 Ω | 4.00 Ω |
| Sources that reach 100 dB out of 280 | 280 | 280 |
One caution before reading the rows. Beyerdynamic DT 770 Pro (32Ω) printed a decibel figure with no reference unit, so this page reads it as per milliwatt. If it is really per volt, that model needs far more than the table says. Why the two readings differ by so much.
Every source in the database that drives one of them drives the other. On power, the choice between these two changes nothing about what amplifier you need.
1 source stays below the audible-hiss threshold with the DT 770 Pro (32Ω) but crosses it with the DT 240 Pro (Schiit Mjolnir 3).
280 of the 280 sources here reach 100 dB on both. That count is about power only — the output-impedance and hiss lines above are separate questions, and a source can pass this one and fail those.
The gap between these two in decibels does not change with volume — it is a property of the two headphones. What changes is the size of the numbers, and it changes fast: every 10 dB costs ten times the power. The row that matters is the one nearest the level you listen at, and for most people that is nearer the top of this table than the bottom.
The DT 770 Pro (32Ω) is more demanding than 72% of the 567 non-electrostatic models in this database; the DT 240 Pro than 60%. Both figures use the same measure as the rest of the site: whichever runs out first against a 2 V, 100 mW dongle, voltage or power.
| dB SPL | DT 240 Pro power | DT 240 Pro voltage | DT 770 Pro (32Ω) power | DT 770 Pro (32Ω) voltage |
|---|---|---|---|---|
| 80 | 0.01 mW | 21 mV | 0.03 mW | 28 mV |
| 85 | 0.04 mW | 37 mV | 0.08 mW | 50 mV |
| 90 | 0.13 mW | 65 mV | 0.25 mW | 90 mV |
| 95 | 0.40 mW | 0.12 V | 0.79 mW | 0.16 V |
| 100 | 1.3 mW | 0.21 V | 2.5 mW | 0.28 V |
| 105 | 4.0 mW | 0.37 V | 7.9 mW | 0.50 V |
105 dB is included because forum power figures are usually quoted there or higher. It is also a level that damages hearing in minutes — how many minutes is its own calculator.
| Source | Price | Headroom, DT 240 Pro | Headroom, DT 770 Pro (32Ω) | Output impedance | Noise |
|---|---|---|---|---|---|
| JadeAudio JA11 | $20 | 13.5 dB | 10.8 dB | 0.5 Ω | 1.7 µV |
| FiiO KA11 | $29 | 21.7 dB | 19.0 dB | 0.7 Ω | 1.7 µV |
| FiiO BTR11 | $36 | 13.5 dB | 10.8 dB | 0.5 Ω | 8.0 µV |
Of the 280 sources here, 280 reach 100 dB on both. That is the easy axis. 69 of them also publish an output impedance low enough for both under the one-eighth rule and a noise figure that stays below the audible-hiss threshold with both — the rest either fail one of those or never printed the number at all, and 208 of them are in the second group.
The cheapest of the 69 is the JadeAudio JA11, at $20. It leaves 13.5 dB of headroom on the DT 240 Pro and 10.8 dB on the DT 770 Pro (32Ω), its output impedance is 0.5 Ω against a one-eighth limit of 4.25 Ω and 4.00 Ω, and its noise figure puts the hiss floor 22 dB and 24 dB below the 20 dB SPL this site treats as the point where a quiet room stops hiding it.
Cheapest that satisfies three published numbers is not the same as best, and none of it is about how either headphone sounds. To put either model against a source this page does not mention, or to change the target loudness, use the amplifier matcher.
| Model | As printed | Tolerance | Standard |
|---|---|---|---|
| DT 240 Pro | 5 - 35.000 Hz | not printed | not printed |
| DT 770 Pro (32Ω) | 5 - 35.000 Hz | not printed | not printed |
Beyerdynamic prints the same thing for both the DT 240 Pro and the DT 770 Pro (32Ω): 5 - 35.000 Hz.
DT 770 Pro (32Ω): Beyerdynamic prints one range for the whole DT family page, the same figure for every impedance version.
Neither range has a tolerance printed beside it, and that is the whole of what this section can tell you. The two sheets print the same range, which is itself a hint about how much the number is worth. A ±dB figure is what turns a range into a specification, and of the 490 models whose maker prints a range, 58 print it.
None of this is a measurement. What each maker publishes, and what it is worth, is set out in the frequency response audit.
Each model has a page of its own with the full source list, the hiss estimate and the provenance of every figure above: Beyerdynamic DT 240 Pro and Beyerdynamic DT 770 Pro (32Ω). Each figure on this page is labelled on those pages with where it came from, including the ones Beyerdynamic never published — what that maker publishes, counted.